MSX cassette page
The MSX cassette tape page
On this page I have documented my 20 year experience with cassette tapes on MSX!
You find my experiments and programs I use for:
- tricks to read troubled tapes
- use another MSX as cassette recorder
- use a PC or cd player as cassette recorder/player (handy if you have a MSX without disk drive)
My current interest for the MSX cassette system is to be able to use MSX 1 computers for i/o control without the need for disk systems.
As you can see this is perfectly possible nowadays with the aid of a PC (i use my notebook as MSX cassette system!).
If you want to run programs on a MSX computer without diskdrives you will find here the tricks and tools to do that.
The MSX cassette system
On a MSX without disk drive the only way to work with files is using the cassette system of MSX. And since MSX 1 computers and some MSX 2 types do not have a disk system most of us started working with MSX listening and cursing that slow and noisy cassette tape system.
In fact the cassette system for storing files on MSX is not that bad. The cassette routines are quite smart in detecting speed differences, the standard MSX routines automatically can work with differences in tape speed and are quite forgiving in outputlevel and differences in the position of the cassette read head alignment. Also speed is slow (1200 baud) or not that slow (2400 baud). Note that MSX is very week in detecting load errors.
All you want to know about the technical details and programming bios calls of MSX can be found in the MSX Red book .
Hardware circuit diagrams can be found in the service manuals on the hardware page .
As an example of how to use the tape related MSX BIOS calls programs see these sources of routines to read and write the screen contents from and to tape by M.C. de Jong.
When I got my first MSX computer (a Toshiba HX-10) i tried to use my simple cassette recorder but it failed all the time. So i bought a WH Smith tape system that is optimised for computer systems: variable output level, can be controlled by the MSX (the MOTOR command, hear the clicks!) and has the option of no/quiet/normal speaker output. A very nice device and i could read all the tapes and record at 2400 baud.
Tricks
Getting the MSX reading tapes does require some tricks often:
- Head alignment: Use a small screwdriver to turn a bit the screw next to the cassette recording head to align the tape. A good MSX cassette tape recorder as the WH SMith type has a hole for this purpose. Listen to the tone and optimise for the pitch as sharp as possible.
- Cleaning: keep the head of the tape recorder clean with alcohol and a clean wipe.
- TV/monitor interference: disconnect the TV or monitor from the MSX and listen to the sound if hum and hiss are becoming less. I used thos trick for some very difficult to read tapes.
- High volume: the reading results may become better if the cassette recorder is set to as loud as possible.
- Retry: note that MSX cassette files are not checked for errors! So it is possible to see the program being loaded and then crashing in all sorts of ways. Retry then with any of the tricks above. At least check what is on the tape with the TAPDIR program : it shows all blocks (basic programs, binary programs, ascii text files or 'unknown' blocks.
Copying MSX cassette tapes
To copy a MSX cassette tape there is more than one way:
- Copy the output of the cassette recorder on another cassette recorder. A method with low chance of success but it might work.
- Use a program like COPMSX to copy all blocks one by one to another tape. This program not only allows to copy the cassette tape contents but can also convert from 1200 to 2400 baud or the other way around. Here you find the program with assembler (TASM) source , written in 1985 for MSX and adapted in 2001 to english and MSX-2.
- Record the output of the cassette recorder on a PC with a soundcard. With any wave editing program (i like Cooledit on Windows, but any program on any platform will do) you can clean up the wave file, filter out hum (50 Hz for example) and improve the volume (normalize). Be carefull with filtering! And make sure that the recording level is optimal: no clipping!!!, not too soft either. 44KHz mono 8 bit is fine, 22KHz also works fine but 44 KHZ allows more editing experiments.
The resulting wave file can be stored on a cassette tape again or stored on an audio cd or just played back from the PC. Ofcourse only a cassette recorder can be stopped and started with the Remote control by the MSX, otherwise you have to stop and start playback manually.
If you store the wave file on an audio or have enough disk space: use 44KHz 16 bit stereo.
Using mp3 format or other compressed formats will work if you set the quality settings high enough, for example 320Kb for mp3 works from p3 players.
New tricks
Cassette recorders are quite low quality (lofi, not hifi) audio recording devices. 2400 baud is the maximum speed you can achieve with these devices. And cassette tapes can break, wear, loose high tones in the end.
Now there are several ways to use the cassette interface without that old- fashioned cassette recorder:
- use another MSX (preferrably with disk drive) as source
- use a PC with soundcard as the ultimate cassette recorder
Ofcourse you need to have either one of these devices! But if you are reading this article, it is quite certain you use a computer with decent sound facilities.
MSX as cassette recorder
When I bought my second MSX computer ( a Spectravideo X'Press SVI.738 with a 360KB diskdrive) i wanted to continue using my first MSX computer (remember, the Toshiba HX-10) and checked if the output of the Spectravideo could be send to the Toshiba (CSAVE on the SVI.738 and CLOAD on the HX-10). It does not work by just connecting output to input (you have to make your own cables anyway) , the signal needs to be amplified (10x was enough). See the next diagram for a simple opamp based amplifier and the connector.
Simple to construct on experimenters board. I took the easy way by using the + 12V and - 12 V from the MSX cartrdige connector as shown in the next figures.
PC as cassette recorder
Record the output of the cassette recorder on a PC with a soundcard. With any wave editing program (i like Cooledit on Windows, but any program on any platform will do) you can clean up the wave file, filter out hum (50 Hz for example) and improve the volume (normalize). Be carefull with filtering! And make sure that the recording level is optimal: no clipping!!!, not too soft either. 44KHz mono 8 bit is fine, 22KHz also works fine but 44 KHZ allows more editing experiments.
The resulting wave file can be stored on a cassette tape again or stored on an audio cd or just played back from the PC. Ofcourse only a cassette recorder can be stopped and started with the Remote control by the MSX, otherwise you have to stop and start playback manually between the blocks.
The PC is such a good recorder that you can do some editing which makes laoding much faster: triple the speed to 3600 baud! Ofcourse this only works when the sample frequency is high enough: 44KHz is required.
Audio CD player as cassette recorder/player
Of course this is only a playback facility! Record the cassette output as described above (or use one of the tools below) and convert the separate blocks to Wave (PCM 44 KHz 16 bit stereo files). Burn these wave files as separate tracks to an audio cd and play the tracks as needed by the MSX loading program.
Using mp3 format or other compressed formats will work if you set the quality settings high enough, for example 320Kb for mp3 works from mp3 players.
You can combine the typical MSX header (the block with the long header and the small data block) and the data block as one track, make sure there is some silence between header and datablock.
Note that the idea of using a audio CD as source of cassette formatted data is not new, Aackosoft produced aCD sequentiel CD with games and an improved loader routime. The CD is in cas format on funet, here you have the MSX Games Collection sequential CD first track and third track (wave format).
MSX Cassette tape format related PC tools
WAVer by Eduardo Robsy Petrus
This PC program Find it here!
TAPE2HDD by Martin Korth author of No$MSX
Tape2HDD cpc/msx tape reader converts the cassette recorder output to files stored on the PC.
To be found at http://nocash.emubase.de/msx.htm
CasLink by Alexey Podrezov
The CasLink project is at http:/www.geocities.com/wierzbowsky/
CasLink is the module that can upload files to MSX via a simple audio cable. The upload can be performed from any PC sound card, CD player or cassette recorder. The CasLink application encodes files in MSX format into 11025Hz 8-bit mono WAV sound file. Two speeds are supported - 1200bps and 2400bps. High speed seems too be always working if PC's sound card is good. I didn't try to upload files to MSX from CD player yet, but I will definitely do this in a few days. I'm 100% it will be working as good as from PC's sound card.
CasLink is created primarily for MSX users who don't have floppy disk drives in their MSX computers. It will also be a relief for those, who have their disk drives broken. You will be able (again) to play your favorite games on your MSX with the help of CasLink. The later version of CasLink will also support decoding of files sent from MSX via cassette interface, so the CasLink will become a true bi-directional support application that will allow to use driveless MSX for creating your own projects.
CasLink supports encoding of the following MSX formats:
BAS - tokenized basic programs
BAS/DAT - detokenized basic programs (ASCII formatt) and raw data files
BIN - binary images of ROM cartridges with staartup code
ROM - images of ROM cartridges
CasLink supports encoding of the following BIN and ROM formats:
BIN - 8/16/24 kb
ROM - 8/16/24/32 kb
CasLink also supports multi-file mode that allows to upload games up to 131072 bytes (1 MegaRom) long to MSX. With 2400bps speed it takes 'only' 12 minutes (grin), but as far as I know NO ONE has ever managed to upload a MegaRom game to real MSX via cassette interface. Multi-file mode supports encoding up to 10 files into a single WAV file. Multi-file mode allows to upload several binary modules with or without a special basic loader before them (some games have LDR basic loaders). If only binaries are uploaded, each of them prepares MSX for uploading of the next binary, so you don't need to type BLOAD after each binary is uploaded to MSX.
To upload a file (or files) to MSX you need to type LOAD, CLOAD or BLOAD command (depending on what is uploaded) on MSX only once and to play the pre-generated WAV file with any media player from DOS or Windows.
MSXCas2Files WebSite
On the site http:/www.terra.es/personal7/miguel.colom/ you will find the programs (with source code included!)
MSXCas2Files
This program reads a wave file recorded from an analog MSX tape, that is analized and decoded, to recover the files that where originally saved on the tape. This version can handle the BSAVE, SAVE, ASCII and tokenized-ASCII formats.
Regenerador
It lets you read a WAV file recorded from an MSX tape and generates another WAV file, noiseless and a regenerated signal. It's quite useful for hard-to-load programs... or those which don't even load.
WMSXF2W
On http:/www.dlcsistemas.com/msx/html/utilities.html you find:
WMSXF2W, MSXF2W
utility to create playable .WAV files from binary .BIN files, ascii files, and tokenized files. It's great to load on the old MSX the games you have in the PC for the emulator.
MSXTAP
Msx Tape loader : Originally it's a program made by Zoran Majcenic for linux in order to get all data from the sound blaster or a RAW sound file in the MSX tape format and convert them to binary file.
WAVGLUE
Wave Glue: It's a tool to merge various sound .wav files into a single one. Even you can indicate to set a pause between them.
Self-extracting MSX MegaROM games
At http:/cax.narod.ru/msx/packed by Stanislav Borutsky (CAX)you find tools to create self-extracting MegaROM games:
a) you can store 7-9 games on the same 720K floppy disk instead of only 5 uncompressed games;
b) you can significantly reduce the loading time of the game, especially if you do it via MSX tape interface.
Developed by Josēicente (WYZ) and Stanislav Borutsky, MicroWAVer is a tool that converts MSX files to audio files (WAV format).
You can load them into your MSX by connecting your PC or diskman or portable MP3 player, handheld or even smartphone via the cassette interface.
Just type bload"cas:",r and play the audio file on your sound device connected to the MSX.
MSX Tape
http:/amgomez.eresmas.net/ for some tools and information (in spanish)
Previous page: Do It Yourself
Next page: Slot extender